Menu
Cart

Shifter base for NV3500 swap from 1994-2004 Dodge Ram + 1994-2000 Dakota



*** For OE replacement see the complete kits instead. ***


Shifter base for custom conversions using NV3500 transmissions sourced from:

  • 1994-2004 Dodge Ram 1500
  • 1994-1995 Dodge Ram 2500 "light duty"
  • 1994-1999 Dodge Dakota - V8 only
  • 2000 Dodge Dakota - V6 & V8 only
    • (Dodge sales code DDC)
    • NOT FOR USE IN THESE VEHICLES - see complete kits
  • Does NOT FIT NV4500 (iron case w/ aluminum top; NV3500 is all aluminum)
  • Does NOT FIT AX15 (1992-1999 Dakota V6)
  • Does NOT FIT 1999-2000 Dakota trucks w/ 4 cyl - see Jeep listing
  • Does NOT FIT 2001-2004 Dakota trucks - see Jeep listing
  • For all other NV3500 models, see separate listings; they are NOT universal!
  • Configured for shifter cup receptacle height of 1/4" as original to these models only
  • IF transmission was rebuilt or replaced, it MAY REQUIRE A DIFFERENT BASE. If you install the wrong one it will not work properly and could cause damage. Height can only be confirmed by removing shifter base and measuring transmission as shown in last pic.

A Hurst stick is required (NOT included, sold separately). Other brands and homemade sticks are discouraged. Stick mount has 3/8"-24 threaded holes spaced 7/8" apart on center + mating serrations for a Hurst stick on one face. Due to larger mounting threads (3/8"-24), sticks that use 8mm mounting bolts (most OE, "non-TKO" Lokar, others) will not work. Lokar TKO sticks can be mounted but only to the smooth side of the stub. To select the proper parts:

  • Wait until new transmission is installed to buy shifter parts
    • Remove existing shifter base if present
    • Sit in vehicle, in driving position, with all interior trim (dash, console, etc) in place
  • Define desired knob location in space (neutral position):
    • Measure height from base flange to desired knob location = overall height
    • Measure side & rear offsets from receptacle bore to desired knob location
    • See this diagram for clarification
  • Study the Hurst stick page for shapes that meet your needs
    • Allow 3-6" for stick mount height
    • Choose a stick and see what fulcrum heights are compatible with it (see chart)
    • Check overall height (see chart: stick height + mount height = overall height)
  • Confirm chosen combination achieves desired knob location and that fulcrum height works with stick length selected
    • Consider various stick & stub combinations to optimize
    • Note long sticks on angled mounts will strongly offset knob to left (can be 5-6"+)
    • Note OE dust boot is short and exposes stick mount which helps in tight situations
    • Options E & F require a Hurst stick directly mounted on side w/ serrations

Stub fulcrum height options (critical to optimizing leverage for short throw):

Option For stick length stick mount height stick mount angle boot type upcharge
A 10" 4.3 vertical Billet Plus default
B 12" 4.8 vertical Billet Plus +$10
C 12"+ 5.8 vertical OE (short) +$20
D 14"+ 6.6 angled 14 deg left OE (short) +$30
E 15"+ 5.5 angled 14 deg left Billet Plus +$30
F 18"+ 5.75 angled 14 deg left Billet Plus +$40
G 8" 4.7 angled 11 deg left OE (short) +$10
H 6" 4.2 vertical OE (short) +$10
  • Stick length = point-to-point distance from mount hole to knob thread
  • Stick mount height = distance from base flange to stick bolt hole (affects knob height)
  • Fulcrum height = distance from lower ball to fulcrum pin; varies by option, not published
    • Warning: Follow stick length guide to avoid excess effort & component failure
  • Core Shifter kits for early Dakota use Option E w/ 0292 stick
  • Core Shifter kits for Ram use Option F w/ 0295 stick

Kit includes pre-installed OE lower pivot cup, mounting hardware, dust cover boot, and instructions. The base is built by Core Shifters using proven components inside a custom housing. This kit has many superior features & components, integrated into a unique, exclusive assembly:

  • Forged heat-treated billet steel gear selector stub
  • Hardened steel cross-pin & stainless steel fulcrum pivot ring
  • Self-centering cross-gate bias springs with heat treated spring seats
  • Glass-reinforced polyamide fulcrum socket with steel wear clips
  • Rubber oil control seal with steel retaining ring
  • Extruded aluminum housing with Spirolox steel support ring
  • Zinc-plated laser-cut steel cover with heat-treated spring retainer straps
  • CNC-machined billet aluminum base
  • Vibration-resistant serrated flange head steel retaining bolts
  • Rubber dust cover boot (style varies)
  • High quality & outstanding value!

We Also Recommend